50 Comments

  1. Linda Roman on July 3, 2021 at 2:02 am

    I would LOVE to use this on my bow window which I absolutely cannot afford to replace

  2. kimchee94112 on July 3, 2021 at 2:05 am

    That 14.4V sander is a museum piece!

  3. Johnny Morales on July 3, 2021 at 2:06 am

    I’m interested in the wood hardener, but the actual details are lacking in the video as you go straight to the filler. How strong is the wood after you soak it with the hardener? I don’t expect it to be like a whole piece of wood, but it would be nice to know if the strength is increased as a result of the hardener rebinding the rotted wood.

  4. Gareth Anthony Clark on July 3, 2021 at 2:06 am

    You had me at "Woody"!
    Thanks for the video. I have a task to restore wooden window frames at my offices , in Cape Town, which have been neglected for years. With a bit elbow grease and a good product, I am sure I can make them look like new.
    I think for any wooden furniture or fixtures, they need to be maintained regularly or you will make unnecessary work yourself!

  5. Roger A Schafer on July 3, 2021 at 2:07 am

    Very sloppy work. Shake the bottle first, mask off the area adjacent to the area being worked. In this case mask off the stones. You allowed the solution to run out of the wood chasm on to the stone and look at the residue. All of this can be prevented by preparing the area for the treatment. This product is very good by the way and works well.

  6. Ted Rosato on July 3, 2021 at 2:08 am

    by woody bc epox my window rotted learned new good tip

  7. JID 340 on July 3, 2021 at 2:11 am

    Nice option if no trees are left on earth

  8. Bill Prezioso on July 3, 2021 at 2:13 am

    Yea I’ll take minwax wood hardener and bondo cures faster time is money

  9. im1dc on July 3, 2021 at 2:14 am

    Thanks for the demo of this very necessary product. I learned something today!

  10. MMelody M on July 3, 2021 at 2:14 am

    Can I use this on my mother’s old wooden steps in the basement? Should you also do the back of the steps with this product?

  11. go barbless on July 3, 2021 at 2:14 am

    Would I get the same or similar results using isopropyl alcohol in place of the denatured alcohol you used in the video to smooth the finish?

  12. MinHongJi woodstudio 솔터공방 on July 3, 2021 at 2:16 am

    hi…I made a wood window after watching your video. Thank you for being an inspiration to me.

  13. John Smith on July 3, 2021 at 2:17 am

    You Woody works great but can you layer the product? I had a low spot I would like to level after repairing my wood sill with Woody…..thanks….

  14. Walter Lefferts on July 3, 2021 at 2:18 am

    You Forgot your GLOVES and Safety Glasses I think ! Stay SAFE out there : ))

  15. hung vu on July 3, 2021 at 2:19 am

    Can i put it in a plastic bag and mix it, then squeeze it where it needs?

  16. Stephen Jeffrey on July 3, 2021 at 2:20 am

    Why don’t you use linseed oil putty to fill the holes and then a linseed oil paint? Traditional methods work better ..

  17. Diamond Back on July 3, 2021 at 2:20 am

    I’m a professional window repairer. I live in northern climates of the us. Chicago land area. Do you have it on shelves or is it online purchase from a web site. On average I would need 1 to 2 gallons of petrifier and several large cans of the woody for an average job.

  18. F Brown on July 3, 2021 at 2:21 am

    What did you mix the p c woody on? What type of board?

  19. Frank Lempka on July 3, 2021 at 2:22 am

    Awesome product, thank you!

  20. Sonsus on July 3, 2021 at 2:26 am

    I would have cleaned all the drips off the wall.

  21. Billy Fincher on July 3, 2021 at 2:26 am

    YOU would save money by putting in a new window sill

  22. Paul Smallriver on July 3, 2021 at 2:29 am

    Unless the rotted sill, in this case, is removed, you won’t know if there is rot elsewhere. Replace the sill.

  23. Captain Howdy on July 3, 2021 at 2:31 am

    This is EXACTLY what I was looking for! Great video!

  24. G H on July 3, 2021 at 2:31 am

    What are the pros and cons of the PC-petrifier and PC Woody versus 3M rotted wood restorer and 3M Bondo wood filler?

  25. Gregg B on July 3, 2021 at 2:33 am

    This type of repair is great if you are going to sell the place. Unfortunately the wood surrounding the patches often continues to deteriorate. This ultimately leads to replacing the entire part.. Been there/ done that.

  26. BMPCC4k tech on July 3, 2021 at 2:36 am

    Can you wood hardener PC Petrifier be used to stabilize wood? Thank you

  27. JungleYT on July 3, 2021 at 2:36 am

    I assume I can get it on Amazon? I’d like to get that 2-part Epoxy to fill in ruts on an old window seal so I can sand it smooth to finish. Should I treat it first with that petrifier?

  28. cameraz99 on July 3, 2021 at 2:37 am

    I have a window sill with about a 5-inch section of damp, spongy wood. Do I have to dig out all the wet wood first, or just apply the wood hardener over it? Thanks!

  29. Donald on July 3, 2021 at 2:38 am

    Only good on horizontal surfaces. Runs right off a vertical surface.

  30. Lebron Jameslol on July 3, 2021 at 2:40 am

    I got a small ice cream scoop to measure it. Using it to repair a few rafter tails. I was going to replace but before I started I noticed the roofer using peel and stick underlayment and thats a huge mess so Im going those route since Im no where near ready for a new roof. Hope it works

  31. monk loss on July 3, 2021 at 2:41 am

    Can I use this stuff to repair subfloor ?

  32. Rita Powell on July 3, 2021 at 2:43 am

    Thanks 4 demo

  33. Allen Brock on July 3, 2021 at 2:44 am

    Awesome I’m definitely going to try some of this

  34. IJnet on July 3, 2021 at 2:45 am

    Smooth level area with alcohol/finger.

  35. John Smith on July 3, 2021 at 2:45 am

    Just bought some from Amazon…exactly what I was looking for…

  36. Miguel A Cordero on July 3, 2021 at 2:46 am

    Bondo dry in a few minutes

  37. Bill Prezioso on July 3, 2021 at 2:47 am

    As a painter I would’ve protected the stone especially if this is a historic building

  38. William Smith on July 3, 2021 at 2:48 am

    A guy I work for bought some of this for us to use around a project as a possible replacement for what I already use (wont mention product name ) or to use along side it.
    The stuff is very hard, stuck to the floors we patched with it and other various items. My main issue was how stiff it is. I dont know if it was how long it sat on the shelf before it was sent to us but, it was really tough to mix together. I do a lot of various repair work and it was tougher than anything I’ve used before.

  39. DJ DJ on July 3, 2021 at 2:49 am

    like the video but don’t understand why you didn’t fix the wood rot on the left side before painting

  40. Christoph Resmerowski on July 3, 2021 at 2:49 am

    1 Gallon $40.19 + 96 oz. PC- Woody Wood Epoxy Paste $ 66.68…. Really ??
    I go with Bondo any day. 17 Bucks a gallon @ Walmart.com.

  41. Michael Fakhraee on July 3, 2021 at 2:49 am

    What is the name of Epoxy please, I could not find it

  42. Sourov Sarkar on July 3, 2021 at 2:51 am

    What’s the difference between your product and a normal wood hardener and wood filler?

  43. Damāko on July 3, 2021 at 2:51 am

    Super cute girl, and super product, PC Woody is my go to when repairing damaged wood.

  44. Robert Thomer on July 3, 2021 at 2:51 am

    This may be fine on a horizontal surfaces, but what about fascia boards or vertical surfaces. I noticed that there wasn’t much concern when you applied the PC-Petrifier onto the sill, it freely ran down the stone facade of your 1800’s farmhouse. How difficult was that to clean up? Gloves anyone?

  45. alexjav21 on July 3, 2021 at 2:51 am

    On the directions it suggests drilling small holes for deeper penetration. Any tips on how far apart to space these holes?

  46. Kyle Foster on July 3, 2021 at 2:52 am

    A joint on the top rail of my hot tub developed rot that abuts the back of the fiberglass of the tub. Is PC Petrifier safe to use on fiberglass?

  47. Panda Plumbing on July 3, 2021 at 2:54 am

    Might have been better to strip all the paint from the whole window frame first, and then fill any damaged parts, then paint the whole window frame again, to make it all look good, and not just the window cill.

  48. DDEENY on July 3, 2021 at 2:55 am

    I’d recommend the use of a rubber glove and smooshing the filler into the hole manually to get it into all of the little nooks and crannies before smoothing off with a putty knife.

  49. hung vu on July 3, 2021 at 2:55 am

    Where can i order this set of product? My window nose rotten out. Thanks

  50. Phil Ramsey on July 3, 2021 at 2:56 am

    Bondo would the same and I bet it is a lot cheaper

Leave a Comment