Install outdoor inline cable gland connector on waterproof junction box.
Install outdoor inline cable gland connector on waterproof junction box.
Video shown how to make a hole using step drill onto plastic surface. Vernier caliper was used to measure the external diameter of the connector as well as the inner diameter drilled using the step drill.
this video, is not helping you (your ratings) or the consumer. thanks for the intent, not for the content.
No utility knife? LOL
Can I buy this crap on eBay from Hong Kong
My gland hurts.
whats the point of measuring it to fit when u juss ripped it out with the needle nose…ahaha!!!
Te grande el guego
Hole was to big especially sinve you were using vernier calipers followed by a pair of scissors you borrowed from a museum. Also the dome gland has a rubber washer and not an ‘O’ ring. Then you forgot to first push the grommet in place. The grommet is the rubber ring that you referred to as a stopper.
All you had to do was cut it out as it is designed to be done. No drilling No risking a stigmata to the palm of your hand SIMPLES
How not to do it !!!!
OMG Please do not make any more video like this…
The way you handle the drill, the scissors from your grandma, the reason to drill, caliper measure the hole… omg omg omg
What you’ve been looking for the PU Chemical for your electrical enclosure gasket foam with Waterproof and fireproofing function, should be here https://youtu.be/ds2ih8MVMVM
can anyone tell me what those wire connectors are called, with the o-rings? and are they IP65 rated?
Thumbs up for entertaining. 🙂
Really stupid idea coz the hole for cable gland is already there.. U just need to poke it out 😂😂
Good job getting the job done.
You should do it more carefully and with much better technique.
Jeujiaoiqhhji27
I almost learned something. We need an update to see how it actually works.
This was ment to be a funny video right? Lmao@ keep drilling and measuring until you drill a whole the size of the knockout… classic.
I hope that caliper is calibrated and certified.
What a shit head. First, that type of junction box is meant to just poke a small hole in that thin spot and then just push your wires through. Second, You spend 5 mins carefully measuring and using your step bit to get the perfect size hole for your cable gland and once you finally get it you end up gaping the hole out to who the hell knows what size with those Haggard ass scissors and putting your gland in a hole that is much too big. Lastly the gland is missing a couple pieces. Basically, you succeeded in turning an easy 5 minute job into a shit show. I wish there was a way to get back the 3:09 I just wasted but alas, I am shit outta luck. Thanks for the mild chuckle
Instructions unclear. I’m now Jesus on both palms of my hands.
Helko
Lbg tu dah ade kan 😂
Not only just horrible but the finished product u showed didn’t have the front cap to hold the cable tightly..
Cutout too big and no rubber seal under the nut!
How To Not Properly Drill A Junction Box 😂😂
halo well come back again
There’s a knock out piece and there’s no need for a drill . It would be much faster and easier. Thanks anyway.👍🏻
are you kidding?!!!
Very poor drilling technique. Drilling towards your hand will eventually come back to "bite you". Also when you are "trimming" ID of hole, use a round file. Makes it simple, fast and safe. Good luck.
this is awful
3rd step drill lolol.
And he ended up going maximum anyway.
Just use the knock-out provided…geez!!
How NOT TO do this correctly – look away any DIYers before you hurt yourselves…
Well that went wrong and he glided through it like it went well….. 🙂
What you’ve been looking for the PU Chemical for your this waterproof junction box gasket foam with Waterproof and fireproofing function, should be here https://youtu.be/ds2ih8MVMVM
Is this Ladka from Taxi?
The finished product was wrong, you didn’t have the bottom gland clamp screwed on.😀